| Versions |
  |
|
| Author |
 Topic  |
|
mige0
6 Posts |
 Posted - 26 déc. 2011 : 12:50:30
|
quote:
It been a long time!! thanks to all! I have my nuvi855 connected to my car, with audio out enabled throught the cradle, no audio from internal speaker (no dummy plug) and rear view camera connected when I use the reverse gear.
These are the pinouts a discover, they are all from the craddle, you have to route them to the hirose:
I will upload a video to show you how its working.
Pin 1 -12V
Pin 2 -12V
Pin 3 -DeviceID GND
Pin 4 -DeviceID
With a resistance connected between this two you can have:
8,1 kohm ->Garmin Serial Cable Slave
3,6 kohm ->Garmin Serial Cable Master
15,4 kohm ->Power Cable
2,15 kohm ->Vib (I'm using this one)
Pin 8 - 12V(negative)
Pin 9 - 12V(negative)
Pin 10- Audio Right
Pin 11- Audio Left
Pin 12- Audio Ground
Pin 13- Mic
Pin 14- Mic Ground
Pin 15- Camera detection (When this one is connected to ground, enables the video camera. I am using it with a relle conected to the reverse light, works perfect)
Pin 29- Video In Ground
Pin 30- Video In
Pin 31- Cradle ID Ground
Pin 32- Cradle ID (With a resistor between this two, you can get:
.38V -> 7,4kohm -> Volvo
.2V -> -> Car (This one is the cradle I have)
.0V -> -> Development (I don t know what this is for)
I still have some noise, but It's much lower since I hooked all grounds together. Maybe I have problems in alternator.
Thanks all again!
PD.I will upload a video to my site ebancora.com.ar
Anybody who did spot a "mute" signal to be output from the navi ?
This would allow to interface directly with car sets that are prepared for phones.
the "mute" signal should go low (connecting to ground) anytime audio is output by the navi, which tells the car set to automatically switch to the phones input no matter what source currently is selected (CD, FM, MP3 ...)
Best
Michael |
 |
|
|
vanmoto
USA
1 Posts |
Posted - 19 mai 2012 : 21:06:33
|
Did anybody find out if the Nuvi supports mute out?
quote:
Originally posted by mige0
quote:
It been a long time!! thanks to all! I have my nuvi855 connected to my car, with audio out enabled throught the cradle, no audio from internal speaker (no dummy plug) and rear view camera connected when I use the reverse gear.
These are the pinouts a discover, they are all from the craddle, you have to route them to the hirose:
I will upload a video to show you how its working.
Pin 1 -12V
Pin 2 -12V
Pin 3 -DeviceID GND
Pin 4 -DeviceID
With a resistance connected between this two you can have:
8,1 kohm ->Garmin Serial Cable Slave
3,6 kohm ->Garmin Serial Cable Master
15,4 kohm ->Power Cable
2,15 kohm ->Vib (I'm using this one)
Pin 8 - 12V(negative)
Pin 9 - 12V(negative)
Pin 10- Audio Right
Pin 11- Audio Left
Pin 12- Audio Ground
Pin 13- Mic
Pin 14- Mic Ground
Pin 15- Camera detection (When this one is connected to ground, enables the video camera. I am using it with a relle conected to the reverse light, works perfect)
Pin 29- Video In Ground
Pin 30- Video In
Pin 31- Cradle ID Ground
Pin 32- Cradle ID (With a resistor between this two, you can get:
.38V -> 7,4kohm -> Volvo
.2V -> -> Car (This one is the cradle I have)
.0V -> -> Development (I don t know what this is for)
I still have some noise, but It's much lower since I hooked all grounds together. Maybe I have problems in alternator.
Thanks all again!
PD.I will upload a video to my site ebancora.com.ar
Anybody who did spot a "mute" signal to be output from the navi ?
This would allow to interface directly with car sets that are prepared for phones.
the "mute" signal should go low (connecting to ground) anytime audio is output by the navi, which tells the car set to automatically switch to the phones input no matter what source currently is selected (CD, FM, MP3 ...)
Best
Michael
|
|
|
|
Topic |
|
|
|
| This page was generated in 1,08 seconds. |
 |
|
- 
- 
Nuvi Proprietary Plug Pinouts
