| Author |
 Topic  |
|
glaros
9 Posts |
 Posted - 20 mars 2009 : 06:20:18
|
Thanks a lot for the link. I have now managed to
download the application. I will interface this
program with GT31 GPS from Locosys.
Cheers. |
 |
|
|
gpspassion
93402 Posts |
|
|
glaros
9 Posts |
Posted - 20 mars 2009 : 11:09:15
|
I think I know what you may mean. You believe
there might be a problem if i simply run the
application as it is (without setting/changing
parameters, etc), watching only signal level,
response and debug views. Will GT31 come out
of synch even then?
Thanks. |
|
|
|
gpspassion
93402 Posts |
Posted - 20 mars 2009 : 11:15:45
|
| No as long as you don't send any commands you should be ok. The older versions of SiRFdemo also forced you to switch to a SiRF binary and that could create problems as the baudrate was changed in the process, now you can get detailed info too in NMEA mode. |
Discounts and Assistance/Réductions et Assistance (Club GpsPasSion) / Où commencer? |
|
|
|
glaros
9 Posts |
Posted - 20 mars 2009 : 11:23:05
|
Ok, thanks for the quick reply,that's great.
GT31 works at constant baud rate of 38400.
I wished it could change down to 4800, since
I want to use it with MS Autoroute 2007 as a real
time GPS receiver, but this application is only
compatible with GPS at 4800 baud.
Anyway, that's another story.
Cheers.
|
|
|
|
spiiiguy
13 Posts |
Posted - 20 mars 2009 : 20:25:28
|
does anybody know how to connect to a garmin c550 using this software and usb or bluetooth? My sirf firmware needs a downgrade since webupdater did me in. I tried installing sirfdemo & the uart/usb software
I get error code 10 just trying to start the driver. |
Edited by - spiiiguy on 20 mars 2009 20:26:30 |
|
|
|
gpspassion
93402 Posts |
|
|
scalor
11 Posts |
Posted - 04 juil. 2009 : 21:38:28
|
i have a problem, in a usglobalsat mr350P gps that work perfectly in nmea output, when i try to switch between nmea output and sirf output, i obtain only this string in the receiver output view
255(0xFF) Error Data
and in the error view
Comm CE_break
|
|
|
|
saimhe
Lithuania
134 Posts |
Posted - 04 juil. 2009 : 23:41:45
|
quote:
Originally posted by scalor
only this string in the receiver output view
255(0xFF) Error Data
and in the error view
Comm CE_break
Did you try every possible baudrate at this point? |
|
|
|
scalor
11 Posts |
Posted - 05 juil. 2009 : 08:55:31
|
i try 2400 that work the nmea protocol in the other baudrate i can't view the nmea string
When i try to change protocol i obtain only this
in error view
warning setcommstate()failed in CSerialComm::open
warning SetComm(0x1000)() failed
warning SetupComm()failed
comm:CE_FRAME
comm:CE_BREAK
....
i have an other question, the 1 PPS output it's enable when there is the fix or must be enable by sirfdemo ? because i have wired the probe of the oscilloscope but there isn't the 1pps signal ! |
Edited by - scalor on 05 juil. 2009 20:51:23 |
|
|
|
bogdan.dumitru
Romania
33 Posts |
Posted - 30 oct. 2009 : 11:29:19
|
just for the knowledge base:
Nokia LD-3W
transmit serial message:
sirf mode: PSRF100,0,38400,8,1,0
nmea mode: A0A20018 81020101 00010101 05010101 00010001 00010001 00019600 012BB0B3 |
Edited by - bogdan.dumitru on 30 oct. 2009 11:29:38 |
|
|
|
jukivili
2 Posts |
Posted - 07 déc. 2009 : 01:28:36
|
Nokia LD-4W (GSWLT3.2.5NOK_3.3.01.01-CL31B1.00):
"Action -> Switch to SiRF Protocol" works fine (bt link goes down, after reconnect it is running in sirf-mode).
"Action -> Switch to NMEA Protocol" does NOT work (bt/gps go out of sync, need to power cycle), but manual NMEA switch works with 0 baud.
"Action -> Transmit Serial Message...": a0 a2 00 18 81 02 01 01 00 00 01 01 05 01 01 01 00 00 00 01 00 01 00 01 00 01 00 00 00 93 b0 b3 |
Edited by - jukivili on 07 déc. 2009 02:02:30 |
|
|
|
JulienS
France
3 Posts |
Posted - 25 janv. 2011 : 19:16:10
|
Hi Everyone, and especially Carl@sirf if you're still there:
I'd need to run SirfDemoPPC on a windows CE 6.0. I could hardly download the software from the internet, as sirf.com is not available anymore. I installed it, and it doesn't seem compatible with my OS. Is there a way to make it work ?
If someone has experience about this... |
|
|
|
Allycat
United Kingdom
59 Posts |
Posted - 25 janv. 2011 : 19:44:24
|
Hi,
SiRFdemoPPC was intended to run with Windows Mobile and generally the "stripped down" Win_CE devices have too many software modules missing.
It depends what you want to do, but have you seen/tried "SirfTech" which manages most of the SiRF functions and has wider platform support:
http://w5.nuinternet.com/s660100031/SirfTech.htm
Cheers, Alan. |
|
|
|
JulienS
France
3 Posts |
Posted - 26 janv. 2011 : 13:43:33
|
Thanks Alan,
SirfTech works fine. I also managed to run SiRFDemo 3.87 from my laptop through ActiveSync. For this I use :
- Franson GPSGate 2.6.0.367 on the laptop (input = ActiveSync)
- Franson GPSGate 2.6 build 347 BETA for Windows CE .NET on the device (output = activesync)
Julien |
|
|
|
Topic |
|
- 
- 
SiRFdemo tutorial (static navigation)
